Dynamic EngineeringメーカーPMC-4U-CACIの使用説明書/サービス説明書
ページ先へ移動 of 33
DYNAMIC ENGINEERING 435 Park Dr., Ben Lomond, Calif. 95005 831-336- 8891 Fax 831-336-3840 sales@dyneng.com www.dyneng.com Est. 1988 User Manual PMC-4U-CACI Quad UART - Dual Synchronous Serial Data Int.
Hardware and Software Design • Manufacturing Services P a g e 2 PMC-4U Quad UART - Dual Synchronous Serial Data Interface PMC Module Dynamic Engineering 435 Park Drive Ben Lomond, CA 95005 831-336-8891 831-336-3840 FAX This document contains information of proprietary interest to Dynamic Engineering.
Hardware and Software Design • Manufacturing Services P a g e 3 Table of Contents PRODUCT DESCRIPTION 6 THEORY OF OPERATION 9 ADDRESS MAP 10 PROGRAMMING 12 REGISTER DEFINITIONS 13 PMC4U_BASE 13 PMC4.
Hardware and Software Design • Manufacturing Services P a g e 4 Interfacing 28 CONSTRUCTION AND RELIABILITY 29 THERMAL CONSIDERATIONS 29 WARRANTY AND REPAIR 30 SERVICE POLICY 31 OUT OF WARRANTY REPA.
Hardware and Software Design • Manufacturing Services P a g e 5 List of Figures FIGURE 1 PMC-4U BLOCK DIAGRAM 6 FIGURE 2 PMC-4U INTERNAL ADDRESS MAP 10 FIGURE 3 PMC-4U UART ADDRESS MAP 11 FIGURE 4 P.
Hardware and Software Design • Manufacturing Services P a g e 6 Product Description PMC-4U-CACI is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC-4U is capable of providing multiple serial protocols both synchronous and asynchronous with a wide range of baud rates.
Hardware and Software Design • Manufacturing Services P a g e 7 An EXAR XR16C854 implements the UART interface. This quad UART device is compatible with the industry standard 16550 UART, but is equipped with 128 byte FIFOs, independent Tx and Rx FIFO counters, automatic hardware/software flow control, and many other enhanced features.
Hardware and Software Design • Manufacturing Services P a g e 8 There is also a master interrupt enable that can be set to gate the interrupt onto the PCI bus. The interrupt status is still available in a status register even when the master interrupt enable is off.
Hardware and Software Design • Manufacturing Services P a g e 9 Theory of Operation The PMC-4U is designed for transferring data from one point to another with a variety of serial protocols.
Hardware and Software Design • Manufacturing Services P a g e 1 0 Address Map REGISTER OFFSET FUNCTION TYPE PMC4U_BASE 0X00 base control read/write PMC4U_STAT 0X04 status read read PMC4U_MSK 0X08 in.
Hardware and Software Design • Manufacturing Services P a g e 1 1 REGISTER OFFSET FUNCTION PMC4U_UART_DATA 0X00 UART read/write data PMC4U_UART_IEN 0X04 UART write interrupt enable PMC4U_UART_ISTAT .
Hardware and Software Design • Manufacturing Services P a g e 1 2 Programming Programming the PMC-4U requires only the ability to read and write data from the host. The base address is determined by the PMC Carrier board. The base address refers to the first user address for the slot in which the PMC is installed.
Hardware and Software Design • Manufacturing Services P a g e 1 3 Register Definitions PMC4U_BASE [0X00] PMC-4U Control Register Port read/write CONTROL BASE DATA BIT DESCRIPTION 31-22 spare 21-20 t.
Hardware and Software Design • Manufacturing Services P a g e 1 4 SCC Tx A OUT_4 (188) SCC Rx A AUX_IN_0 (enhanced hysteresis 188) SCC Rx Clk AUX_IN_1 (enhanced hysteresis 188) SCC RTS A AUX_OUT_0 (.
Hardware and Software Design • Manufacturing Services P a g e 1 5 UART Tx C OUT_6 (RS423) UART Rx C IN_6 (RS232) UART Tx D OUT_7 (RS423) UART Rx D IN_7 (RS232) Master interrupt enable when ‘1’ gates all interrupts through to the PCI host. When ‘0’ the interrupts can be used for status without interrupting the host.
Hardware and Software Design • Manufacturing Services P a g e 1 6 PMC4U_STAT [0X04] PMC-4U Status Port read only STATUS DATA BIT DESCRIPTION 31-2 spare 1 interrupt out 0 interrupt status FIGURE 5 PMC-4U TX C ONTROL REGISTER BIT MAP Interrupt out indicates that an interrupt is asserted on the PCI bus.
Hardware and Software Design • Manufacturing Services P a g e 1 7 PMC4U_SCC_IVEC [0X0C] PMC-4U SCC Interrupt Acknowledge/Vector Read A read from this address causes the SCC interrupt acknowledge signal to be asserted. If an interrupt condition exists in the SCC, it will respond by placing an interrupt vector on the local data bus.
Hardware and Software Design • Manufacturing Services P a g e 1 8 Parallel termination resistors are supplied on each differential pair along with a switch to allow the user to select which lines are terminated and where.
Hardware and Software Design • Manufacturing Services P a g e 1 9 PMC4U_SCC_A_CNTL [0X18] PMC-4U SCC Channel A Control Register read/write This address is used to access all of the channel A registers. In order to access a register other than this base register, the register number is first written to this address.
Hardware and Software Design • Manufacturing Services P a g e 2 0 PMC4U_UART_A [0X40] PMC-4U UART A Base Address This is the base address for the eight register addresses associated with UART A. Figure 3 gives an overview of these registers and their functions.
Hardware and Software Design • Manufacturing Services P a g e 2 1 PMC4U_IRUPT/PMC4U_IRUPT_CLR [0XE0] PMC-4U Interrupt Latch read status/write clear INTERRUPT STATUS DATA BIT DESCRIPTION 4 SCC interr.
Hardware and Software Design • Manufacturing Services P a g e 2 2 Interr upt s PMC-4U interrupts are treated as auto-vectored. When the software enters into an exception handler to deal with a PMC-4.
Hardware and Software Design • Manufacturing Services P a g e 2 3 Loop- back The Engineering kit has reference software, which includes external loop- back tests for the SCC and the UART. These tests require an external cable with the following pins connected.
Hardware and Software Design • Manufacturing Services P a g e 2 4 PMC PCI Pn1 Interface Pin Assignment The figure below gives the pin assignments for the PMC Module PCI Pn1 Interface on the PMC-4U-IO. See the User Manual for your carrier board for more information.
Hardware and Software Design • Manufacturing Services P a g e 2 5 PMC PCI Pn2 Interface Pin Assignment The figure below gives the pin assignments for the PMC Module PCI Pn2 Interface on the PMC-4U-IO. See the User Manual for your carrier board for more information.
Hardware and Software Design • Manufacturing Services P a g e 2 6 PMC-4U Front Panel IO Pin Assignment The figure below gives the pin assignments for the PMC Module IO Interface on the PMC-4U. Also, see the User Manual for your carrier board for more information.
Hardware and Software Design • Manufacturing Services P a g e 2 7 PMC Pn4 User Interface Pin Assignment The figure provides the pin assignments for the PMC-4U Module routed to Pn4. Also, see the User Manual for your carrier board for more information.
Hardware and Software Design • Manufacturing Services P a g e 2 8 Applications Guide Interf acing The pin-out tables are displayed with the pins in the same relative order as the actual connectors. The pin definitions are defined with noise immunity in mind.
Hardware and Software Design • Manufacturing Services P a g e 2 9 Construction and Reliability PMC Modules were conceived and engineered for rugged industrial environments. The PMC-4U is constructed out of 0.062 inch thick FR4 material. Through hole and surface mounting of components are used.
Hardware and Software Design • Manufacturing Services P a g e 3 0 Warranty and Repair Dynamic Engineering warrants this product to be free from defects in workmanship and materials under normal use and service and in its original, unmodified condition, for a period of one year from the time of purchase.
Hardware and Software Design • Manufacturing Services P a g e 3 1 Service Policy Before returning a product for repair, verify as well as possible that the suspected unit is at fault. Then call the Customer Service Department for a RETURN MATERIAL AUTHORIZATION (RMA) number.
Hardware and Software Design • Manufacturing Services P a g e 3 2 Specifications Host Interface: PCI Mezzanine Card Serial Interfaces: Four UART channels each with an RS422 driver and receiver and an RS423 driver. One synchronous channel with Mil. Std.
Hardware and Software Design • Manufacturing Services P a g e 3 3 Order Information PMC-4U PMC Module with 4 UART channels and 2 synchronous/asynchronous serial channels Programmable baud rates diff.
デバイスDynamic Engineering PMC-4U-CACIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Dynamic Engineering PMC-4U-CACIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはDynamic Engineering PMC-4U-CACIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Dynamic Engineering PMC-4U-CACIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Dynamic Engineering PMC-4U-CACIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Dynamic Engineering PMC-4U-CACIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はDynamic Engineering PMC-4U-CACIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Dynamic Engineering PMC-4U-CACIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちDynamic Engineering PMC-4U-CACIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
