Harbor Freight Toolsメーカー31849の使用説明書/サービス説明書
ページ先へ移動 of 17
31849 ASSEMBL Y & OPERA TING INSTR UCTIONS 7” RABBETING JOINTER WITH ST AND 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb Site at www .
THANK Y OU for choosing a HARBOR FREIGHT T OOLS product. F or future ref erence , please complete the owner’ s record below: Model ______________ Serial No. ______________ Purchase Date _____________ SA VE THE RECEIPT , W ARRANTY AND THESE INSTR UCTIONS.
W ork Area T O A V OID RISK OF PERSONAL INJUR Y , EQUIPMENT D AMAGE, FIRE AND SHOCK, MAKE SURE Y OUR WORK AREA IS: F ree of damp , wet or rainy conditions . F ree of children (ne ver let them handle tools or machinery). W ell-lit. Clean and uncluttered.
Grounding/V oltage W arning Common household current is 110-120 volts . As long as the outlet used with the tool is rated from 110-120V there will be no complications using it with household receptacles. Plug the tool into a 110-120V properly grounded outlet protected b y a 15-amp , dual element time dela y or circuit break er .
The Stand Step 1) Attach the F ront Side Plate (#16A) to both of the Side Link Plates (par t #19A). Inser t two Screws (#17A) through F ront Side Plate and through Side Link Plate. Slide on W ashers (#7A) and Nut (#6A). Tighten into place . Repeat for the other side - see Figure 1.
Step 9) Attach the T apping Plate (#25A) with Right and Left T apping F enders (#23A & #27A) to the Left Protecting Plate (#26A). Insert the Screws (#17A) with head on the outside of the Plate. On the inside, slide on Washer (#7A) and Nut (#6A)-see Figure 2.
Cutterhead Guard W arning: Be ware of sharp blade when installing the Cutterhead Guard. Step 1) Inside of the Spring Knob (#37) there is a Spring (#36) which returns the Guard toits position abov e the Cutterhead after a cut. T o create tension in the Spr ing, tur n the Spring Knob (#37) bef ore inser ting the post.
Step 2) Flip the square jib so that its end sits against the flat par t of the Plate (18)-see Figure 7. Step 3) Using an Allen Wrench, attach this assemb ly to the F ence (#11) with the three Hex Scre ws (#24)-see Figure 6.
Fence Adjustments The F ence (par t #11) is assembled to the front of the Inf eed T ab le (#33). The F ence can be moved across the T ab le and can be tilted 45 degrees right or left by using the Handle P ole (#29). Step 1) T o move the F ence (#11) across the T able , turn the Handle Pole (#29) to loosen.
Step 4) If the knife is not aligned at one or both sides, loosen Bolts (60) which hold the Knife Lock Bar (61). Use a knife setting gauge (not included) to make sure that the knife at each end of the cutter is the same height. Repeat for the next two (2) knives as is fitting.
Step 8) Secure the rear table in position and remove the feeler gauge. Step 9) Lower the infeed table and place a straight edge on the outfeed table so that it e xtends out o ver the cutterhead. Step 10) T urn the cutterhead by hand until the knif e is at its highest point at each end of the cutterhead.
T ur ning the Jointer ON and OFF Step 1) T o tur n the Jointer ON, press down on the green b utton on top . Step 2) T o tur n OFF the Jointer, press do wn the red b utton on the bottom. IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE , DO NOT OPERA TE THE T OOL .
Unpac king UNP A CK AND CHECK CONTENTS When unpacking y our Jointer with Stand chec k to mak e sure the f ollo wing parts are included. If an y parts are missing or broken, please call HARBOR FREIGHT T OOLS at 1-800-444-3353.
P ar ts List - Jointer Assemb ly P ar t # Description Quantity Par t # Description Quantity 1 Outf eed T ab le 1 36 Spring 1 2 Bearing Housing 1 37 Spring Knob 1 3 Ball bearing 1 38 Retainer 1 4 Cutte.
Stand Assemb l y Dia gram Each of the P ar t Numbers below correspond to the Stand Assemb ly and has the suffix “A” - see P ar ts List on P age 13.
Jointer Assembly Diagram - See Parts List on Page 14 #31849 Page 16.
White White Black Black Wiring Dia gram #31849 Page 17.
デバイスHarbor Freight Tools 31849の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Harbor Freight Tools 31849をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 31849の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 31849の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 31849で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 31849を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 31849の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 31849に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 31849デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。