Harbor Freight Toolsメーカー35740の使用説明書/サービス説明書
ページ先へ移動 of 11
3.5 GALLON P AR TS W ASHER Assembly and Operating Instructions 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.
SKU 35740 For technical questions, please call 1-800-444-3353. Page 2 SPECIFICA TIONS Characteristic V alue T ank Dimensions 17-3/8" x 14-1/4" x 8-3/4" Max. Solvent Capacity 3-1/2 Gallons Pump Output 50 GPH Electrical Requirements .7 Amps @ 1 10V , 60Hz Weight 15-1/2 lbs.
SKU 35740 For technical questions, please call 1-800-444-3353. Page 3 8. USE EYE PROTECTION. Solvents can cause serious eye damage . W ear ANSI approved chemical splash safety goggles. Goggles are available from Harbor Freight T ools. When cleaning, be especially careful as solvents can be forcibly ejected from fluid and air passages.
SKU 35740 For technical questions, please call 1-800-444-3353. Page 4 VOL T AGE W ARNING Common household current is 1 10-120 volts. As long as your tool is rated from 1 10V -120V there will be no complications using this tool with household receptacles.
SKU 35740 For technical questions, please call 1-800-444-3353. Page 5 UNP ACKING When unpacking, check to make sure the following p arts are included. All sizes listed below are approximate. If any part s are missing or broken, please call Harbor Freight T ools at the number on the cover of this manual.
SKU 35740 For technical questions, please call 1-800-444-3353. Page 6 ASSEMBL Y Lid Handle Assembly S tep 1: Get out the LID HANDLE (#10); and two each of the SCREWS (#12), Lock W ashers (#13), and NUTS (#14). S tep 2: Attach HANDLE to LID (#2) as shown in Figure 1.
SKU 35740 For technical questions, please call 1-800-444-3353. Page 7 Cord Clamp/Ground Wire Installation S tep 1: As viewed from the inside, insert one SCREW (#20) through the right side of the CORD CLAMP (#19) and the inside of the T ANK (#1). Make sure CORD CLAMP is covering the cord of the PUMP (#6).
SKU 35740 For technical questions, please call 1-800-444-3353. Page 8 Nut (# 23) Power Cord (# 17) Swi t c h Box (# 15) Scre w (# 20) W asher (# 21) Lock W asher (# 22) Ground Wires Black Wire (fro m .
SKU 35740 For technical questions, please call 1-800-444-3353. Page 9 Remaining Assembly S tep 1: Attach the FIL TER (#7) to the PUMP (#6), as shown in Figure 4. S tep 2: Attach the SPIGOT (#9) to the PUMP , as shown in Figure 4. S tep 3: Set the P ARTS TRA Y (#3) in the T ANK (#1).
SKU 35740 For technical questions, please call 1-800-444-3353. Page 10 P ARTS LIST NO. QTY . DESCRIPTION 1 1 T ank 2 1 Lid 3 1 Parts Shelf 4 1 Fusible Link Lid Arm 5 9 Rivet 6 1 Pump 7 1 Filter 8 1 Pu.
SKU 35740 For technical questions, please call 1-800-444-3353. Page 11 P ARTS DIAGRAM NO TE : Some par ts are listed and shown for illustr ation pur poses only and are not av ailable individually as replacement par ts.
デバイスHarbor Freight Tools 35740の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Harbor Freight Tools 35740をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 35740の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 35740の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 35740で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 35740を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 35740の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 35740に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 35740デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。