Harbor Freight Toolsメーカー45885の使用説明書/サービス説明書
ページ先へ移動 of 12
10 INCH COMPOUND SLIDE 10 INCH COMPOUND SLIDE 10 INCH COMPOUND SLIDE 10 INCH COMPOUND SLIDE 10 INCH COMPOUND SLIDE MITER SA MITER SA MITER SA MITER SA MITER SA W W W W W ASSEMBL Y AND OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our W eb site at http://www .
Page 2 SKU 45885 Specifications I TEM D E SC R I PT I ON P ow er C ons um pt i on 110 V A C , 60 H z, 1650 W at t s , 2. 2 H P No l oad: 5A ; S t ar t up: 15A P o we r Co r d 6- 1/ 2 f e et , U L app .
Page 3 SKU 45885 3. Keep children away . Children must never be allowed in the work area. Do not let them handle machines, tools, or extension cords. 4. Store idle equipment . When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children.
Page 4 SKU 45885 17. Guard against electric shock . Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerator enclosures. 18. Replacement parts and accessories . When servicing, use only identical replacement parts.
Page 5 SKU 45885 Installation 1 . Place the Saw on the solid workbench capable of supporting the weight of the Miter Saw and all work pieces. (Do not carry the unit by the Handle or misalignment of the components may occur .) 2. Using a pencil, mark through the saw Base (1 18) holes onto the workbench.
Page 6 SKU 45885 Preparation to Cut Stock 1 . Before cutting stock, verify that it fits the base and fence properly and secure in place. The photos on the next page show the proper way to lay the stock on the base for cutting. These methods will keep the Saw Blade from binding with the stock, and keep it from rolling.
Page 7 SKU 45885 9 . T urn on the saw by pressing in on the T rigger Handle (56). 10. When the Saw Blade comes to full speed, bring the Saw Blade down and begin cutting slowly through the stock. W arning: A void personal injury . Do not disable the Saw Blade safety Shield (67).
Page 8 SKU 45885 7 . Remove the existing Saw Blade and replace with another 10 inch blade. The new Saw Blade has an arrow on it that must be pointing in the same direction as the large arrow on the outside of the Fixed Shield (10). Caution: Never use saw blades larger or smaller in diameter than 10 inches, and rated less than 5000 RPM operation.
Page 9 SKU 45885 3 . Remove the Brush Holders (48) and examine the old Brushes. If the existing brushes are worn past 3/16 inch in length, or if the spring or shunt wires are burnt, they must be replaced. Never replace just one brush. If the brushes are only dirty , and not worn down, you can use a pencil eraser to clean the brush tips.
Page 10 SKU 45885 Adjusting Depth of Cut Bevel Stop to 90 Degrees 1 . Position saw bevel stop at 90 degrees and loosen bevel Adjusting Handle (73). 2 . Tilt cutting arm all the way up to 90 degrees position on the Scale and retighten Adjusting Handle.
Page 11 SKU 45885 .
Page 12 SKU 45885 REV 04/03 45885.p65 10/15/03, 10:41 AM 12.
デバイスHarbor Freight Tools 45885の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Harbor Freight Tools 45885をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 45885の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 45885の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 45885で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 45885を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 45885の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 45885に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 45885デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。