Harbor Freight Toolsメーカー54461の使用説明書/サービス説明書
ページ先へ移動 of 9
18 GUAGE, 5/8”-2” AIR BRAD NAILER ASSEMBL Y and OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our W eb site at http://www .harborfreight.com For technical questions and replacement parts, please call 1-800-444-3353 Model 54461 ® Copyright c 2003 by Harbor Freight T ools ® .
Page 2 SKU 54461 Specifications Save This Manual Y ou will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. W rite the invoice number on the inside of the front cover .
Page 3 SKU 54461 9. Maintain tools with care . Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician.
Page 4 SKU 54461 Operation Unpacking When unpacking, check to make sure the parts listed on page 8 are included. If any parts are missing or broken, please call Harbor Freight T ools at the number on .
Page 5 SKU 54461 FIGURE 1 Seqential T rip Safety T rigger (31) Magazine Latch (39) Heel Cushion (79) W arning! This Nailer has a Sequential T rip safety mechanism. With the trigger pulled, the unit will fire each time the nose of the Nailer contacts a surface.
Page 6 SKU 54461 Loading Nails Operating the Nailer 1. Attach the Nailer to the air supply at the Air Connector (not included) which is already connected to the Air Inlet (33). See FIGURE 1 . Start your compressor and make sure it is set to between the recommended 60-1 15 PSI and not over the maximum 130 PSI.
Page 7 SKU 54461 Note: Have the following problems repaired by a qualified service technician. 1. Problem : Air leaking at trigger valve area. Probable Cause : Damaged 0-rings in trigger valve housing. Solution: Replace 0-rings. Then re-check contact safety trip mechanism.
Page 8 SKU 54461 NOTE : Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. Parts List Part No.
Page 9 SKU 54461 Assembly Drawing 91 100 B0300-070 90 89 9 11 12 13 14 10 9 11 2 3 4 6 8 87 7 5 1 32 31 30 29 28 93 92 27 24 26 25 23 22 21 20 19 24 18 17 16 15 36 34 33 38 35 101 37 83 39 40 41 42 43.
デバイスHarbor Freight Tools 54461の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Harbor Freight Tools 54461をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 54461の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 54461の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 54461で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 54461を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 54461の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 54461に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 54461デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。