Harbor Freight Toolsメーカー95014の使用説明書/サービス説明書
ページ先へ移動 of 16
PRESSURIZED ABRASIVE BLASTER Model 95014 ASSEMBL Y AND OPERA TING INSTR UCTIONS ® © T O PREVENT SERIOUS INJUR Y , READ AND UNDERST AND ALL W ARNINGS AND INSTRUCTIONS BEFORE USE. without the express written consent of Harbor F reight T ools. Copyright 2006 b y Harbor F reight T ools ® .
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the saf ety war nings and precautions, assemb ly , operating, inspection, maintenance and cleaning procedures, par ts list and assembly diagr am. K eep your in voice with this manual.
9. Dress properl y . Do not wear loose clothing or jew elr y as they can be caught in moving par ts. Protectiv e, electrically non-conductiv e clothes and non-skid f oot- wear are recommended when working. W ear restr ictive hair co ve r ing to contain long hair .
SKU 95014 For technical questions, please call 1-800-444-3353 P A G E 4 15. Replacement parts and accessories. This product is to be repaired and ser viced only by a qualified technician. When this product is ser viced, only identical replacement par ts should be used.
30. W ARNING! Abrasive blasting with media containing crystalline silica can cause serious or fatal respiratory disease. Exposure to crystalline silica ma y cause silicosis (a serious lung disease), cancer , and death. Exposure to aluminum oxide (a dust generated from material removing processes) can result in eye, skin, and breathing irritation.
9. Provide w orkers with training that includes inf or mation about health effects , work practices, and protectiv e equipment for crystalline silica. 10. Repor t all cases of silicosis to State health depar tments and to OSHA or the Mine Saf ety and Health Administration (MSHA).
SKU 95014 For technical questions, please call 1-800-444-3353 P A G E 7 ASSEMBL Y INSTR UCTIONS T o Attac h The Handle Bar s: 1. T o attach the two Handle Bars (6) to the T ank (1), la y the T ank on a flat, lev el surf ace with its Handle Bar mounting brac kets f acing up .
SKU 95014 For technical questions, please call 1-800-444-3353 P A G E 8 3. Slide a Wheel W asher (51) onto each end of the Wheel Axle (5). (See Figure B.) 4. Place a Wheel (2) onto each end of the Wheel Axle (5). Then, slide a Wheel W asher (51) onto each end of the Wheel Axle.
SKU 95014 For technical questions, please call 1-800-444-3353 P A G E 9 OPERA TING INSTR UCTIONS Abrasive Selection: 1. The type of media chosen will greatly influence the amount of time needed to clean a par ticular surface area. 2. Sandblasting media include silicon carbide, glass bead, walnut shell, brass bead, and alumina.
7. IMPORT ANT TIP: If the humidity is 90 to 100%, the W ater T rap (17) will not be able to tr ap all of the moisture in a 3/4 full T ank (1). It is recommended to reduce the amount of media, load more frequently , and empty the W ater T rap more often.
4 . T ur n the Air Supply V alve (18) and Throttling V alve (18A) to the “ON” position. At this point, the T ank (1) will begin to pressurize. (See Figure F .) 5 . Check f or leaks at the T ank Filler Cap (12) and along all hoses and fittings as the system pressurizes.
SKU 95014 For technical questions, please call 1-800-444-3353 P A G E 1 2 8 . P oint the Blast Gun at the wor kpiece so that the media will str ike the surf ace of the workpiece at about a 45 degree angle. 9 . Squeeze the Control Lever (42C) of the Blast Gun to release the media.
SKU 95014 For technical questions, please call 1-800-444-3353 P A G E 1 3 2. Before each use: Inspect the general condition of the Pressurized Abrasive Blaster and its accessories. Check for loose screws, misalignment or binding of moving par ts, crac ked or brok en par ts, damaged air hoses , and any other condition that may affect safe operation.
SKU 95014 For technical questions, please call 1-800-444-3353 P A G E 1 4 TR OUBLESHOO TING P roble m P ossible S olution Blast flow surges. 1. Air pressure too low. Increase a ir pressure. 2. Too much media . Adjust Abrasi v e Control Valve. Excessive media consumption.
NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not av ailable individually as replacement par ts. P ARTS LIST & ASSEMBL Y DIA GRAM - AIR BLASTER SKU 95014 For technical questions, please call 1-800-444-3353 P A G E 1 5 P a rt # D e scription Q ty.
SKU 95014 For technical questions, please call 1-800-444-3353 P A G E 1 6 P ARTS LIST & ASSEMBL Y DIA GRAM - BLAST GUN P a rt # D e scription Q ty.
デバイスHarbor Freight Tools 95014の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Harbor Freight Tools 95014をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 95014の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 95014の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 95014で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 95014を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 95014の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 95014に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 95014デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。