Jenn-Airメーカー6 918803 Aの使用説明書/サービス説明書
ページ先へ移動 of 24
Custom Pane l Instruc tions Items you w ill need: - Custom Panel Door Fr ont (m ax weight: 16 lbs) o Panel M UST be ¾ inch thick. - Tape Measure - Electric Drill - Torx (T-20) Head Screwdriver - 1/8.
Step 1: Construct the Custom Panel. 1.1 Ensure the custom panel is the sam e size as the pa nel sho wn in the figure below. 1.2 Drill holes in the back of the pane l using the tem plate provided. Follow the instructions on the front of the tem plate. If the tem plate is m issing follow the instructions on f ollowing pa ge.
1.2B Custom panel construction without a tem plate. 1.2.1 Find the center of panel at the to p and bottom and draw and l ine through both points, di viding the pa nel in two. 1.2.2 Drill two 1/8” holes per above figure no more than 3 /8” d eep. 1.
Step 2: Installing Panel Fasten ers. 2.1 Rem ove existing front p anel from dishwasher. 2.1.1 Open door com pletely and r emove the second s crew from the top on both the right and left s ides of the do or. Save the sc rews. 2.1.2 Slide the existing f ront panel up ward approxim ately 1 ½ ” .
2.3 Rem ove the two panel fas teners f rom the face of the control panel on the in ner door. 2.4 Scre w each of the four p anel fasteners into the four 5/ 32” pilot holes prev iously drilled into the back of the wood panel.
Step 3: Mount ing the Handle (Han dle Provided wit h Dishwasher). See Step 3B for Cu stom Handle Inst allation. NOTE: Use these instruct ions ONLY if you are using the sam e handle pro vided with t he dishwasher. You will need t o purchase t wo ¼ - 20 bolts that are 2 ½ inches long.
Step 4: Mo unting the Custom Pane l to the Dishw asher. 4.1 Align the four pan el fastener s with the four holes of the k eyhole slots on the inn er door panel. 4.2 Once all four f asteners are seated, slide the custom panel dow n until the top of the custom panel is flush with the to p of the control p anel.
Step 5: A d just Sp ring Tension on Door. 5.1 If the spring tension on the door is too great then lower the spring on the bracket. 5.2 If the spring tension on the door is not eno ugh then: 5.2.1 Remove spring f rom bracket. 5.2.2 Remove the brack et by rem oving the two screws.
Instructions pour p a nneaux p ersonnalisés Articles nécessaire s : - Panneau de f açade personnal isé pour porte (po ids max. : 16 lb) o Le panneau DOIT avoir u ne épaisseur de 3 /4 po.
Étape 1 : Prépa ration du pan neau personnali sé. 1.1 Découpez le pan neau personnalisé selon les m êmes dimens ions que celles du panneau présen té ci-dessous. 1.2 Percez des trous à l’ ARRIÈR E du panneau en utilisant le gab arit fourni.
1.2B Préparatio n du panneau per sonnalisé sans l e gabarit. 1.2.1 Faites deux repèr es au centr e du panneau, en h aut et en bas de ce lui-ci, et tracez une ligne verticale pour les jo indre et diviser le panneau en de ux. 1.2.2 Percez deux trous de 1/8 po selo n la figure à une profondeur m aximale de 3/8 po.
Étape 2 : Install ation des fixations d e panneau. 2.1 Retire z du lave- vaissel le, le panneau de f açade exista nt. 2.1.1 Ouvrez la porte à f ond et enleve z les deuxièm es vis à partir du haut, à droite et à gauche de la porte. Co nservez ces vis.
2.3 Enleve z les deux fixat ions de panneau, du devant du t ableau de comm ande, sur la contre-porte. 2.4 Visse z chacune des qua tre fixations d ans les quatre a vant- trous de 5/32 p o percés préalablem ent à l’ar rière du panneau en bois .
Étape 3 : Mo ntage de la poignée (p oignée fournie av ec le lave-v aisselle). Consultez l’étape 3B pour l’installation de la poignée personn alisée. REMARQUE : Utilisez ces instructions SEULEMENT si vous utilisez la poignée fournie avec le lave-vaisselle.
Étape 4 : M ontage du panneau per sonnalisé sur le lave-vaisselle. 4.1 Alig nez les quatre fixations de panneau avec l es quatre trous d es fentes ovalisée s du panneau de la co ntre-porte.
Étape 5 : Réglag e de la tension du ressort de la por te. 5.1 Si la tens ion du ressort d e la porte est tro p forte, accro chez le ressort à un niveau plus bas. 5.2 Si la tens ion du ressort d e la porte est ins uffisante : 5.2.1 Décrochez le res sort de son supp ort.
Instrucciones del Pan el Personalizado Artículos Necesario s: - Panel delantero p ersonalizado para la puerta (pes o máx: 16 lbs.) o El panel DEBE ser de ¾ pulg.
Paso 1: Constru cción del Panel P ersonalizado. 1.1 Asegúrese de que el panel per sonalizado sea de l mism o tamaño que el que s e muestr a en la figura siguiente. 1.2 Taladre agujeros en la parte trase ra del panel usando la p lantilla provista. S iga las instrucciones indica das en el frente de la planti lla.
1.2B Construcc ión del panel p ersonalizado si n una plantilla. 1.2.1 Marque el centro del panel en la p arte superior e inferior y trace un a línea conectando am bos puntos, di vidiendo así el pane l en dos. 1.2.2 Taladre dos agujeros de 1/8”, de acuerdo con la fig ura anterior, de n o más de 3/8” de profund idad.
Paso 2: Instalación d e los Suj etadores del Pane l. 2.1 Retire el panel delantero antiguo del lavavajillas. 2.1.1 Abra completam ente la puerta y retire el segundo t ornillo desde el tope en ambos lados (derec ho e izquierdo), d e la puerta. Con serve los tornillos.
2.3 Retire los dos sujetador es del panel s ituados en el f rente del panel de co ntrol en la puerta interior. 2.4 Atorn ille cada uno de los cuatro sujeta dores del pa nel en los cuatro ag ujeros pilotos de 5/32” pr eviamente tala drados en la par te trasera del p anel de m adera.
Paso 3: Montaje de la M anija (M anija suministrada con el lavavajillas). Ver Paso 3B par a la instalación de l a manija pe rsonalizada. NOT A : Use estas instrucciones S OLAMENTE si est á usando la m anija sum inistrada con el lavavajil las. Necesitar á comprar dos pernos de ¼ - 20 bolts de 2 ½ pulgadas de larg o.
Paso 4: M ontaje del Panel Person alizado en el La vavajillas. 4.1 Alinee los cuatro suj etadores del pa nel con los cuatro agujeros d e las ranuras piriform es del panel interior de la puerta.
Paso 5: Ajuste de la Tensión d el Resorte de la Puerta. 5.1 Si la tens ión del resorte d e la puerta es mu y f uerte, baje el resorte en el sop orte. 5.2 Si la tens ión del resorte d e la puerta no es suficiente: 5.2.1 Retire el resorte d el soporte.
デバイスJenn-Air 6 918803 Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Jenn-Air 6 918803 Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJenn-Air 6 918803 Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Jenn-Air 6 918803 Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Jenn-Air 6 918803 Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Jenn-Air 6 918803 Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJenn-Air 6 918803 Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Jenn-Air 6 918803 Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJenn-Air 6 918803 Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。