Anton/BauerメーカーUL-2の使用説明書/サービス説明書
ページ先へ移動 of 12
ULTRALIGHT 2 ( UL-2 ) OWNER’S MANUAL.
.
TO REMOVE / REPLACE BULB NOTE: Only MR-16 type bulbs sho uld be used with the UL2. 1. Pull out on the Thumb Tabs of the Head M odule. 2. Swing Hood open. 3. Remove and replace bulb as necessar y. 4. Close Head Module, insuring that it “clicks ” closed.
INTRODUCTION The Ultraligh t 2 (UL2) is a n extremel y compact, sup er lightwe ight version of the orig inal Ultra light system, designed specific ally for o n-camer a lighting applicatio ns. The Ultra light 2 inco rporate s many uniq ue feature s includi ng: • Included with a AB-60, wide angle bulb.
5/64 Hex Wrench Shoe Sleeve Shoe Mount Thumbwheel Set Screw Be sure the Shoe Sleeve is completely inside the light, otherwise the light may swing back & forth. ¼-20 STUD MOUNT APPLICATION The Ultralight 2 is shipped standard with ¼ -20 Stud Mount for attachi ng to the camera handle.
Stud Mount Application 1/4-20 Screw ACCESSORIES UL2 WEDGE The UL2 Wedge is developed specifically for use with the Anton/Bauer Ultralight 2 on-ca mera light. The UL2 Wedge provides the Ultralight 2 with an additional 20º of down angle lighting for shooting extreme close up camera shots (less than 3 feet).
When properly fitted, the slot in the tab will align with a screw in the center of the hood. The ta b insertion requires a slight force. If the filter assembly is too loose and does not stay in place, bend each side of the tab in opposite dire ctions as show n to provide sufficient holdi ng friction.
UL-SOFT B OX The UL-Soft Box mounts easily to any Ultralight Head Module to sof ten and diffuse light output. The UL-Soft Box is collapsible allowing eas y storage or can fold and swing awa y while remaining on the Ultralight until needed.
BULB SELECTION AND OPERATION Bulbs used by the Ultralight 2 are T ype MR16, tungsten-halogen bul bs. Spot or flood bulbs of any light distribution angle may be used. The Ultralight 2 offers the greatest versatility with the following low voltage bulbs.
WARRANTY IMPORTANT: WARRANTY REGISTRAT ION CARD MUST BE MAILED WITHIN 10 DAYS OF PURCHASE TO QUALIFY FO R THIS WARRANTY. Pro per registration will also enabl e us to send you important update information. We must have the warrant y registration card on file at our CUSTOM ER SERVICE DEPARTMENT t o establish warranty.
.
The worldwide standard The following are registered trademarks of Anton/Bauer, Inc.: ACS, Anton/Bauer, Anton/Bauer Logo, Au tomatique, ComPac, Gol d Mount,HyTRON, Impac, InterActive, InterActive 2000 .
デバイスAnton/Bauer UL-2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Anton/Bauer UL-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAnton/Bauer UL-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Anton/Bauer UL-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Anton/Bauer UL-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Anton/Bauer UL-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAnton/Bauer UL-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Anton/Bauer UL-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAnton/Bauer UL-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。