Olympusメーカー023の使用説明書/サービス説明書
ページ先へ移動 of 42
Instruction Manual Underwater Case PT -023 For the digital camera CAMEDIA C-8080 Wide Zoom ■ Thank you for buying the Underwater Case PT-023. ■ Please read this instruction manual carefully and use the product safely and correctly. ■ Please keep this instruction manual for reference after reading it.
E-1 Disclaimer ● Unauthorised copying of this manual in part or in full, except for private use, is prohibited. Unauthorised reproduction is strictly prohibited. ● OLYMPUS CORPORATION shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from incorrect use of this product.
E-2 1. Keep this product out of the reach of babies, infants, and children. There is the possibility of occurrence of the following types of accidents. Injury by dropping onto the body from a height. Injury from parts of the body getting caught in parts which open and close.
E-3 Batteries ● Use an exclusive lithium-ion battery (Olympus BLM-1) designed for digital cameras. ● Keep the battery's contacts away from damp or humidity; otherwise this could impair performance and/or cause accidents. ● For additional battery cautions, refer to your digital camera's instruction manual.
E-4 For Prevention of Water Leakage Accidents When water leakage occurs while this product is being used, repair of the camera housed in this product may become impossible.
E-5 Handling the Product ● Use or storage of the product at the following locations may cause defective operation, defects, trouble, damage, fire, internal clouding, or water leakage. Always avoid these locations. Places where high temperatures exist, such as in direct sunlight, in a closed vehicle, etc.
E-6 ● Do not perform operations other than specified in this instruction manual, do not remove or modify parts other than specified, and do not use parts other than specified. Any troubles in taking pictures or with the equipment resulting from the above actions shall be outside the guarantee.
E-7 Disclaimer ..................................................................................E-1 Please read the following before using the product ..................E-1 For safe use ................................................................
E-8 Fitting the mode dial knob .................................................... E-22 Insertion of silica gel ............................................................ E-22 Check the loading status. ..............................................
E-9 1. Preparations Check the contents of the package. Check that all accessories are in the box. Contact your dealer if accessories should be missing or damaged.
LCD hood strap Grease for O-rings (White-cap tube) Silica gel Balance weight Pick for removing O-rings Buckle opener Lens cap Buckle open/close lever Buckle hook ❈ Quick View button ❈ Control dial.
E-11 : • Do not exert excessive force onto the lens window or the lens ring. • Take care not to put your fingers etc. over the lens window and the flash diffuser. Note : • Check your image on the LCD monitor. The viewfinder cannot be used to check the image.
E-12 How to Press the Shutter When pressing the shutter lever, press it gently, so that there will be no movement of the camera. Note : • For more detailed information on operating the shutter release, please consult the digital camera’s instruction manual.
E-13 Setting the Zoom Lever When loading the digital camera in the Case, fit the projecting part of the zoom lever of the digital camera into the recessed part of the zoom lever on the inside of the Case. Power Switch Button Operation Method Press the power switch button to switch on the camera power supply.
Boss Buckle E-14 : • If the standard port is attached improperly to the case, water penetration may result. Also make sure that the buckles on the left and right of the standard port are clamped firmly.
E-15 : • The diffusion plate cannot be used when the PPO-05 is mounted. CA UTION Detaching First make sure the case is completely dry. While gently holding the diffusion plate and standard port, slo.
E-16 Removing the TTL cable connector cap TTL flash shooting is possible by uncapping the TTL cable connector on this case (PT-023) and connecting the FL-20 flash case (optional PFL-01) as described in the following procedure.
E-17 Removing the hot shoe cable cap To perform TTL flash shooting when this case is used, connect the hot shoe cable provided with the optional PFL-01 between the connector on this case and the C-8080 Wide Zoom's hot shoe. 1 Turn the hot shoe cable connector cap inside the case counterclockwise to remove it.
E-18 2. Adv ance Check of the Case Advance test before use This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly.
E-19 Advance Test 1. Before installing the digital camera in the Case, immerse the empty Case to the intended water depth to confirm that there is no water leakage. 2. Main causes of water leakage are as follows. The O-ring has not been installed.
E-20 3. Install the digital camera. Check the digital camera. Check the digital camera before loading it in the Case. Battery Confirmation Since the LCD monitor is used for picture confirmation while taking pictures under water, the battery life becomes short.
① ② E-21 Lifting the mode dial knob Pull up the mode dial of the case until it stops, so that it does not interfere with the mode dial of the digital camera. Open the Case. Insert the buckle opener of the accessory into the buckle opening lever as shown in the figure (in direction ) Pull the buckle opener slowly (in direction ).
E-22 Fitting the mode dial knob After the digital camera has been loaded, push down the mode dial of the case from the upper surface of the case and set it so that the lower part of the mode dial of the case on the inside of the case fits properly onto the upper part of the mode dial of the digital camera.
E-23 : • Seal the Case by turning both buckle lock levers down in arrow direction. When one of the buckles is left open, the Case will not be sealed and water leakage will be caused.
Guides E-24 Installation and Removal of the LCD Hood Installation Strongly push the mounting projections of the LCD hood as shown in the figure into the guides above and below the LCD monitor window. Removal Remove the mounting projections of the LCD hood from the guides above and below the LCD monitor window by widening the LCD hood.
E-25 : • After inserting the camera into the case, confirm that the mode dial moves. If it does not move, oil or grease may have gotten on the mode dial. Wipe it clean. CA UTION Try to move the mode dial. After sealing, turn the mode dial knob and confirm that the mode dial of the camera is switched.
E-26 Final Test The final test after loading the camera is explained below. This is the only way to eliminate worry about possible entry of water! Always perform this test. It can be performed easily in a water tank or a bathtub. The required time is about five minutes.
E-27 4. T aking Pictures Under Water How to Use the Hand Strap Pass your hand through the accessory hand strap and adjust the length with the stop button. Take pictures carefully. Confirm the picture on the LCD monitor. This Case uses the LCD monitor to confirm the picture.
E-28 5. Handling After Shooting Wipe off any waterdrop. After underwater shooting, remove any drops of water from the case. Use pressurized air or a soft, lint-free cloth to carefully wipe away any moisture from the hinge between the front and rear lids, the shutter release lever, the handgrip and the buckles.
E-29 Take out the digital camera. Open the case carefully, pull up the mode dial from the upper surface of the case to disengage it from the mode lever of the camera, and then remove the digital camera from the case. : • After opening the case, always put it down it with the O-ring side face-up.
E-30 Wash the Case with pure water. After use, seal the Case again after taking out the camera and wash it sufficiently in pure water as soon as possible. After use in sea water, it is effective to immerse it for a fixed time in pure water to remove any salt.
E-31 6. Maintaining the W aterproof Function Remove the O-ring. Open the Case and remove the O-ring from the Case. Removal of the O-ring Insert the O-ring removal pick between the O-ring and the wall of the O-ring groove. Move the tip of the inserted pick under the O-ring.
E-32 Install the O-ring. Confirm that no foreign matter is attached, apply a thin coat of the accessory grease to the O-ring, and fit the O-ring into the groove.
E-33 : •A lways perform maintenance of the waterproof function even when the Case has been opened to exchange the battery or the image storage during shooting.
E-34 Replace consumable products. The O-ring is a consumable product. Independent of the number of times the Case is used, it is recommended that the O-ring should be replaced by a new one at least once a year. Deterioration of the O-ring is accelerated by the use conditions and the storage conditions.
E-35 7. Appendix Q & A on the use of the PT-023 Q1 : Which digital cameras can be used with this case? A1 : This case is designed exclusively for use with the CAMEDIA C-8080 Wide Zoom.
E-36 (a) Places where the Case can reach high temperatures under direct sunlight or in a car, places with extremely low temperatures, and places with extreme temperature variations (b) Places with ope.
E-37 moisture and dry the Case in the shade. Do not use hot air from a hair drier or the like and do not dry the Case under direct sunlight. Exposure to high temperatures or direct sunlight may cause deformation, discoloration or breakage of the Case and deterioration of the O-ring.
E-38 (3) Damage, deterioration, or deformation of the O-ring (4) Sand, fibers, hair or other foreign matter on the O-ring (5) When foreign matter (sand, fiber, hair, etc.) is stuck to the O-ring grooves or O-ring contact surfaces. (6) Catching of the strap, the bag of silica gel, etc.
E-39 is sufficient for cleaning. • Do not use anticorrosion agents on the metal parts. The metal parts are made of aluminum, brass or stainless steel. Cleaning with pure water is sufficient. • Do not use commercial defogging agents. Always use the original Olympus defogging silica gel.
E-40 After-sale Service ● You will receive the Warranty card from your dealer. Please make sure that the dealer's name, the date of purchase, etc. have been entered. If they have not been entered, immediately ask your dealer to have them entered.
E-41 Olympus digital camera CAMEDIA C-8080 Wide Zoom Available models Dimensions E-41 Specifications ❈ We reserve the right to change the external appearance and the specifications without notice.
デバイスOlympus 023の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Olympus 023をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOlympus 023の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Olympus 023の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Olympus 023で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Olympus 023を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOlympus 023の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Olympus 023に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOlympus 023デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
