OnkyoメーカーRFR-5の使用説明書/サービス説明書
ページ先へ移動 of 12
Thank you for purchasing the Onkyo RF Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new RF Receiver.
2 Care From time to time you should wipe the front and rear panels and the cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a weak solu- tion of mild detergent and water, wring it out dry, and wipe off the dirt. Following this, dry immediately with a clean cloth.
3 Intr oduction About the RFR-5 Most remote controller systems have to be operated by pointing the remote controller directly towards a device. Any obstacle between the remote controller and the device disturbs the operating signal.
4 Possible Set-ups The RF Receiver can be used in several situations: ■ Your devices can be remotely controlled while the RF Receiver is placed in line of sight (situation A). ■ The RF Receiver controls devices placed in an adjacent room (situation B).
5 Installation The following components should be present: RF Receiver, power adapter, 3 IR emitters, Mono cable and 4 screws. Before you install the RF Receiver, you should decide which of the set-ups described on p. 2 apply to your needs. It is recommended to read through the entire User Guide.
6 Mounting The RF Receiver can be mounted to a piece of furniture using the included mounting plate and the 4 screws. Take into account the range and the working angle of the IR blaster as explained on p. 4. Also make sure to place the RF Receiver in a central position aimed directly at your devices.
7 Installation Connecting the Power Adapter When connecting the power adapter it is recommended that you plug the adapter into the RF Receiver before you plug it into the socket. When connected you will see a red LED on the RF Receiver. Note: To avoid interference, the adapter cable should not be placed directly above or below the RF Receiver.
8 Installation Settings As the RF Receiver “ communicates ” with the Chad Remote Controller, you have to set the same Receiver ID (identity) on both appliances.
9 T r oub leshooting Devices do not respond properly ■ Check if the power adapter is connected and the red LED is on. ■ Check if the ID and channel numbers on the RF Receiver match with the ID and channel numbers on the Chad Remote Control (see p.
10 Red LED (continuously on when powered, blinking during RF reception) 16 IDs and 4 CHs 4 outputs for IR emitters Possibility to have multiple RF Receiver in one home not interfering Positioning: freestanding, mounted horizontally or hanging up side down 4.
11 Memo.
Sales & Product Planning Div . : 2-1, Nisshin-cho , Neyaga wa-shi, OSAKA 572-8540, JAP AN T el: 072-831-8111 F ax: 072-833-5222 ONKY O U.S.A. CORPORA TION 18 P ark W ay , Upper Saddle River , N.J. 07458, U.S .A. T el: 201-785-2600 F ax: 201-785-2650 http://www .
デバイスOnkyo RFR-5の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Onkyo RFR-5をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOnkyo RFR-5の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Onkyo RFR-5の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Onkyo RFR-5で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Onkyo RFR-5を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOnkyo RFR-5の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Onkyo RFR-5に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOnkyo RFR-5デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。