Phantom TechメーカーSU0508Lの使用説明書/サービス説明書
ページ先へ移動 of 20
Installation Manual for For Left Hinged Doors Durable. Reliable. Attractive. For door openings up to 36” (914 mm) wide and 81 1/4” (2,064 mm) high Quick and Easy to Size and Install.
Congratulations and thank you for purchasing Sure V iew! The Sure V iew retractable screen is designed and manufactured by Seiki Screen Systems, the world’ s largest manufacturer of retractable screens. Phantom Screens, North America’ s leading brand of retractable solutions, is proud to bring you these innovative products.
4 5 6 7 8 9 10 - 1 1 12 13 14 15 16 17 Getting to Know the Sure V iew Screen ........................... Parts and T ools ................................................................ Measuring the Door Opening .....................................
Getting to Know the Sure V iew Screen Before beginning, become familiar with the Sure V iew Screen and the door on which it will be installed. The Sure V iew Screen can be installed on both in-swing and out-swing doors. In-swing doors open to the inside of the home and require the Sure V iew Screen to be installed on the outside of the home.
| 1 Parts and T ools Before beginning, make sure that all these parts are included in the Sure V iew Screen package. Required T ools Sure V iew Screens can be sized and installed using common household tools. Make sure all necessary tools are available before beginning.
Measuring the Door Opening Now it's time to measure the door opening. The Sure V iew Screen will accommodate a door opening of up to 36” (914 mm) wide and 81 1/4” (2,064 mm) high. If the door opening is smaller than this, the Sure V iew Screen will have to be cut.
(Measured Height) [Length to be cut off] ( 81 1/4” (2,064 mm) - [ ] ) = Sizing the Sure V iew Screen If the door opening is smaller than 36” (914 mm) wide and 81 1/4” (2,064 mm) high, the Sure V iew Screen must be cut.
Cutting the T op and Bottom Rail and Catch Frame Cutting the T op Rail of the Sure V iew Screen is an easy process. 1. Using the “Length to be cut” dimension calculated on Page 7, carefully measure the T op Rail on the end opposite the end cap. Mark on all sides to ensure an even cut.
Cutting the Screen Housing Assembly It is easy to cut right through the Screen Housing Assembly of the Sure V iew Screen using a chop saw or hacksaw . NOTE : All cutting will be done on the upper end of the Screen Housing Assembly . The Mounting Bracket on the Screen Housing Assembly is clearly labeled with CUT and NO CUT zones.
Installing the Screen Housing Assembly 1. Locate the “L” shaped edge of the Mounting Bracket. ( A ) The Mounting Bracket will be positioned with this edge closest to the door . 2. Remove the adhesive strip on the back of the Mounting Bracket and position on the mounting surface.
Installing the Screen Housing Assembly Attaching the Screen Housing Assembly 1. Place the front left corner of the Screen Housing Assembly in the outside edge of the Mounting Bracket. ( C ) 2. Pivot the Screen Housing along this point until the back of the Assembly snaps into the “L” shaped edge on the back of the Mounting Bracket.
Installing the T op Rail 1. Remove the backing on the adhesive strip on the T op Rail. 2. Place the uncapped end of the T op Rail over the Sliding Bar T op Cap and slide the T op Rail into the Mesh Lock Adjuster . Ensure that it ts tightly . ( A ) 3.
1. Insert the Catch Frame into the bottom of the T op Rail End Cap. Ensure that the T op Rail End Cap ts tight to the right side of the door frame. ( D ) 2. Using a level, adjust the Catch Frame along the mounting surface of the door frame to ensure that it is positioned plumb.
Installing the Bottom Rail If the Bottom Rail did not require cutting, it is important to select the correct Bottom Rail for installation. The Sure V iew Screen package comes with two Bottom Rails to accommodate both at and angled door sill. Please refer to ( A ) to determine the correct Bottom Rail.
Installing the Bottom Rail Adjusting the Catch 1. Loosen the screw on the Catch. 2. Move the Catch up a nd down to determine the position where the Latch makes a secure contact with the Catch. Tighten the screw on the Catch to secure it in place. ( D ) 3.
Final Adjustments Adjusting the Mesh The Sure V iew Screen can be adjusted to reduce the amount of mesh discharged from the Screen Housing. This keeps the mesh tight to maintain the effectiveness of the Sure V iew Screen in keeping out unwanted insects.
Service and Maintenance Hints The Sure V iew Screen is designed and engineered to be maintenance free. Please review these helpful hints to ensure the smooth operation of the Sure V iew Screen for years to come: • All moving components used in the Sure V iew Screen are manufactured from a mixture of nylon and other materials.
Help Hotline The Sure V iew Screen was designed for easy sizing and installation. This Installation Manual provides a step by step guide through the entire process.
Sure V iew Screen Limited Lifetime/Non-transferable Manufacturer ’ s W arranty The Sure V iew Screen is warranted by Seiki Screen Systems to be free of manufacturer ’ s defects in materials or wor.
Designed & Manufactured by Seiki Screen Systems ™ Marketed and Distributed by Phantom Screens ® Seiki Screen Systems Call 1-877-446-7180 Or email: info@seikiscreensystems.com www .seikiscreensystems.com Phantom Mfg. (Int’l) Ltd. Call 1-888-PHANTOM Or email: phantom@phantomscreens.
デバイスPhantom Tech SU0508Lの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Phantom Tech SU0508Lをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPhantom Tech SU0508Lの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Phantom Tech SU0508Lの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Phantom Tech SU0508Lで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Phantom Tech SU0508Lを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPhantom Tech SU0508Lの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Phantom Tech SU0508Lに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPhantom Tech SU0508Lデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
