ProFormメーカーPFBE14530の使用説明書/サービス説明書
ページ先へ移動 of 18
Visit our website at www .proform.com new products, prizes, fitness tips, and much more! CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. PFBE14530 Serial No. W rite the serial number in the space above for future reference.
2 W ARNING DECAL PLACEMENT W ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Read all instructions in this manual before using the weight bench. Use the weight bench only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight bench are ade- quately informed of all precautions.
4 Right Side Left Side Note: The terms “right side” and “left side” are determined relative to a person sitting on the bench; they do not correspond to right and left on the drawings in the manual. BEFORE YOU BEGIN Thank you for selecting the versatile PROFORM ® C705 weight bench.
5 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two persons. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
6 3. Attach the Crossbar (4) to the Left Upright (5) with two M10 x 68mm Button Bolts (38), a Support Plate (47), and two M10 Nylon Locknuts (43). Do not tighten the Locknuts yet. Next, attach the Crossbar (4) to the Left Upright (5) with an M10 x 93mm Button Bolt (37), an M10 W asher (41), and an M10 Nylon Locknut (43).
38 7 41 4. Attach a Small Base Foot (14) to the Bench Leg (2) with an M4 x 16mm Screw (39). Press a 50mm Square Inner Cap (25) and a 50mm Notched Square Inner Cap (50) into the Bench Leg. Attach the Bench Leg (2) to the Bench Frame (1) with two M10 x 68mm Button Bolt (38), two M10 Wa shers (41), and two M10 Nylon Locknuts (43).
8 8. Press four 25mm Square Inner Caps (24) into the Backrest T ubes (9). Orient the Backrest T ubes (9) so that the indicat- ed holes are closer to the bottom. Attach the Backrest Bracket (8) to the Backrest T ubes with four M10 x 45mm Button Bolts (35), four M10 Wa shers (41), and four M10 Nylon Locknuts (43).
9 11 .A ttach the Seat (16) to the Bench Frame (1) with an M6 x 63mm Screw (33), an M6 W asher (34), and two M6 x 16mm Screws (40). 11 16 1 34 33 40 12. Slide a Pad Tube (12) into a hole in the Leg Lever (7). Wet both sides of the Pad Tube with soapy water .
10 The weight bench is designed to be used with your own weight set (not included). The steps below explain how the weight bench can be adjusted. See EXERCISE GUIDELINES on page 12 for important exercise information and refer to the accompanying exercise guide to see the correct form for each exercise.
11 AT T ACHING THE CURL POST For some exercises, the Curl Post (10) must be attached to the weight bench. Remove the 50mm Square Inner Cap (25). Slide the Curl Post into the bench Leg (2). Align the adjustment holes in the Curl Post with the adjustment hole in the Bench Leg.
12 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS MUSCLE BUILDING To increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
13 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
14 MONDA Y Date: / / EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts.
M6 W asher (34) M10 Nylon Locknut (43) M4 x 16mm Screw (39) 25mm Round Angle Cap (32) 25mm Square Inner Cap (24) 25mm Round Inner Cap (45) M8 W asher (26) M8 Nylon Locknut (44) M6 x 16mm Screw (40) M6.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user ’s manual for information about ordering replacement parts.
EXPLODED DRA WING—Model No. PFBE14530 R0803A 18 10 40 23 39 11 21 21 30 51 41 37 17 35 43 41 41 24 48 41 41 36 48 34 24 43 47 37 37 38 38 46 39 15 3 37 37 39 46 15 21 11 23 21 39 30 5 43 43 6 37 37 .
Part No. 200004 R0803A Printed in China © 2003 ICON Health & Fitness, Inc. LIMITED W ARRANTY ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate- rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase.
デバイスProForm PFBE14530の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
ProForm PFBE14530をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはProForm PFBE14530の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ProForm PFBE14530の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ProForm PFBE14530で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ProForm PFBE14530を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はProForm PFBE14530の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ProForm PFBE14530に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちProForm PFBE14530デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。