TascamメーカーPA-30の使用説明書/サービス説明書
ページ先へ移動 of 12
» PA -30 Dual Power Amplifier OWNER’S MANUAL 9A09572800.
The T ASCAM P A-30 is a high-performance professional audio po wer amplifier for nearfield studio monitoring and lo w-le vel sound reinforcement. In stereo mode, the P A-30 delivers 30 w atts per channel continuously into an 8 ohm load - with no more than 0.
1) Read these instructions. 2) K eep these instructions. 3) Heed all warnings. 4) Follo w all instructions. 5) Do not use this apparatus near water . 6) Clean only with dry cloth. 7) Do not block any v entilation openings. Install in accordance with the manufacturer's instructions.
• Do not use the P A-30 if the power cord appears frayed or broken. • Do not spill liquids into or on the P A-30 chassis. If the chassis becomes wet, allo w it to dry thoroughly before reconnecting the unit. • Allo w suf ficient space at the top, and bottom of the P A-30 to permit a flow of cooling air .
1. POWER Switch and Indicator A two-position rocker -type switch controls power to the unit. Depressing the upper surface of the switch turns the amplifier on; depressing the lo wer surface turns it of f. The green LED Po wer indicator will light whene ver the unit is on and is connected to a properly functioning source of po wer .
6. INPUTS (A & B, XLR & RCA T ype) Tw o input connectors are provided for each channel: one RCA (phono) jack and one XLR-type female connector . Either connector may be used on a gi ven channel, but both connectors for a single channel should not be used simultaneously .
Input Connections Before making connections to the P A-30 signal inputs, find the nominal output le vel of your signal source (this information is usually gi ven in the Specifications section of the instruction manual).
Output Connections Each channel of the P A-30 will drive a minimum load impedance of 8 ohms. Connecting a load of lo wer impedance will result in current limiting and may trigger the Protection circuits to shut do wn the amplifier . Figure 7 sho ws a normal stereo-mode connection of two indi vidual speakers to the P A-30 outputs.
The P A-30 rear panel includes a switch that selects either normal stereo mode or a special mode termed BTL (Balanced T ransformerless). The setting of this switch determines the maximum po wer av ailable to the load from the P A-30, and also decisively af fects how the load is connected to the amplifier .
Output power at 8 ohms, (1 kHz): 30 W atts minimum RMS per channel in stereo mode, both channels dri ven. (0.05% THD) 60 W atts minimum RMS in BTL (monophonic) mode. (0.08% THD) T otal Harmonic Distortion (1 kHz): 0.05% (30 W atts 8 ohms, STEREO) 0.08% (60 W atts 8 ohm, BTL) Intermodulation Distortion: Less than 0.
T ASCAM P A-30 11 MEMO.
TEAC CORPORATION Phone: (0422) 52-5082 3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan TEAC AMERICA, INC. Phone: (323) 726-0303 7733 Telegraph Road, Montebello, California 90640 TEAC CANADA LTD. Phone: 905-890-8008 Facsimile: 905-890-9888 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada TEAC MEXICO, S.
デバイスTascam PA-30の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Tascam PA-30をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTascam PA-30の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tascam PA-30の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tascam PA-30で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tascam PA-30を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTascam PA-30の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tascam PA-30に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTascam PA-30デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。