Trekメーカー6i, 8i, 9i, 11iの使用説明書/サービス説明書
ページ先へ移動 of 10
C ONTENT S Safety and general guidelines ............................... i F unctions .............................................................. 1 Installation ........................................................ 2-3 Setting the computer .....
1 FUNC TIONS Not all Trek Incite computer models have all these functions. T able 1- F unction abbreviations , names and explanations F unction Explanation Speed Curr ent speed of the bicycle displayed in miles per hour (MPH) or kilometer s per hour (KPH).
2 INS T ALLA TION T ools needed: • Electrical tape • Slot-type screwdriver • Phillips-type screwdriver • Scissors This section explains the steps to install your computer onto your bicycle: .
3 A tt aching the computer wire The computer wire is usually longer than needed. Extra wire length can be diverted by wrapping it around the brake housing prior to routing it down the fork blade or down tube (Figure 9). Make sure the computer wire is not pulled tight when the handlebar is turned all the way to either side.
4 SETTING THE C OMPUTER The computer must be set, or “programmed,” so that it gives its readout in the units preferred by the user , and so that it calculates with the correct wheel size.
5 T o set Clock 1. Cycle Mode to CLK. 2. Hold Mode . 3. Cycle Set to 12 or 24 hour clock. 4. P ush Mode to select clock. 5. Cycle Set to the hour . 6. P ush Mode to select. 7. Cycle Set to the minute. 8. P ush Mode to select. The computer returns to curr ent speed.
6 INCITE 9I AND 11I Setting the 9i and 11i is done by pushing the three buttons in a specific sequence. The button on the side of the computer is the Set button.
7 T o set a custom wheel size 1. Cycle Mode to TME. 2. Hold Set . The wheel selection icon appears in the upper left corner . 3. Cycle Set to your preferred wheel. 4. Cycle Mode to the four-digit number . 5. Press Set . 6. Cycle Mode to your preferred first digit value (see T able 3).
8 CHANGING FUNCTIONS AND O THER NORMAL USE These are everyday tasks that are not explained elsewhere in the manual. Changing mode Once the computer is programmed and installed, it is very easy to use. T o change to different modes (functions), simply press the Mode button(s) at the bottom of the computer .
9 TROUBLE SHOO TING The Incite computer is designed to be easy to install and maintain. However , some people occasion- ally have problems with their computer . Here is a table showing some possible problems, causes, and solutions: T able 4- Common problems and solutions Blank screen Comput er is in shipping mode.
デバイスTrek 6i, 8i, 9i, 11iの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Trek 6i, 8i, 9i, 11iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTrek 6i, 8i, 9i, 11iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Trek 6i, 8i, 9i, 11iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Trek 6i, 8i, 9i, 11iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Trek 6i, 8i, 9i, 11iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTrek 6i, 8i, 9i, 11iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Trek 6i, 8i, 9i, 11iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTrek 6i, 8i, 9i, 11iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。