Black BoxメーカーMDR210A-485の使用説明書/サービス説明書
ページ先へ移動 of 14
MDR210A - 485 900 MHz. Frequency Hopping RS - 485 Master/Slave auto - sensing radio interface. Black Box Corporation – Lawrence, PA - http://www.blackbox.
2 Table of Contents Description………………………………………………………………3 Features………………………………………………………………….4 Serial Port Scanning…………………………………………………5 Application Fields…………………………………………………….
3 Description The MDR210A - 485 uses an embedded 100 - milliwatt, frequency - hopping wireless modem that provides communication between a local RS485 network and a remote network of RS485 connected devices. The MDR210A - 485 will automatically sense the direction of data flow and switch the RS485 and Radio devices accordingly.
4 Features res General Purpose 900 MHz. Spread Spectrum Frequency Hopping Transceiv General MDR210A - 485 Frequency Range 902 to 928 MHz., unlicensed IS M Band Type Frequency Hopping Spread Spectrum Transceiver Frequency Control Direct FM Transport Protocol Transparent networking Channel Capacity Hops through 25 channels.
5 9XSTREAM - 192/96 Radio Introduction The 9XSTREAM - 192/96 radio is a 100 - milliwatt frequ ency hopping wireless modem that communicates with other equipment using a standard 19200 or 9600 - baud asynchronous serial data stream. The radio is half - duplex and can sustain a continuous data stream at the specified data rate.
6 9XStream Frequency Hopping Data Radio FCC Complia nce Warning: Changes or modifications to the 9XStream Data Radio not expressly approved by MaxStream, Inc.
7 Ante nna Antenna Connector MMCX Female Antenna Impedance 50 Ohms unbalanced Approved Antennas Integral wire antenna (factory installed) Astron AXQ9PRLMMCX – 1/4 wave flexible whip Astron AXH900 RP.
8 hop in a different sequence) the two modules will jump to separate channels on the next hop. Using networks, multiple module pairs can operate in the same vicinity with minimal interference from each other. The network parameter is user - defina ble using the MDR210A - 485 Set - up Hop Table.
9 Figure 2a – Generation of Data Packets Data Validity (Cont.) To verify data integrity, a 16 - bit cyclic redundancy check (CRC) is computed for the transmitted data and attached to the end of each data packet before transmission. The receiver will then compute the CRC on all incoming data.
10 Data Packets – A grouping of data to be sent over - the - air. Each data packet contains a header and data that is collected from the data buffer. The size of the packets varies up to 64 bytes depending on how many bytes of data are in the data buffer.
11 Application Notes Why does Sensitivity Matter? Receiver sensitivity is the lowest power level at which the receiver can detect a wave and demodulate data. Sensitivity is purely a receiver specification and is independent o f the transmitter. As the wave propagates away from the transmitter, it attenuates as the distance increases.
12 Application Notes (cont.) Range Receive d Detectable by Detectable by (meters) Power MDR210A - 485 Commercial Radio 100 - 68.526 dBm YES YES 500 - 82.506 dBm YES YES 1000 - 88.526 dBm YES YES 3000 - 92.048 dBm YES NO 5000 - 102.506 dBm YES NO 8000 - 106.
13 Appe ndix A – Specifications General Frequency Range 902 to 928 MHz, unlicensed ISM Band Type Frequency Hopping Spread Spectrum Transceiver Frequency Control Direct FM Transport Protocol Transparent Networking Channel Capacity Hops through 25 channels.
14 FCC Compliance Warning: Warning: This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interferen ce received, including interference that may cause undesired operation.
デバイスBlack Box MDR210A-485の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Black Box MDR210A-485をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBlack Box MDR210A-485の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Black Box MDR210A-485の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Black Box MDR210A-485で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Black Box MDR210A-485を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBlack Box MDR210A-485の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Black Box MDR210A-485に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBlack Box MDR210A-485デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。